รายละเอียด
Sight Glass
SGI ( Refrigerant : HCFC , mineral oil , R22)
Sight glasses are used to indicate:
The SGI/N and SGRI/N are equipped with sensitive indicators that reflects a colour,
depending on the moisture content in the refrigerant.
Type SGI / SGRI
* Refrigerants where lubrication is by mineral oil e.g. HCFC
* Indicates too high water content in the refrigeration system
* Indicates lack of subcooling
* Indicates refrigerant deficiency
* Flare/solder connection or socket type
HCFC | ||||
Type | Version | Connection [in.] | Connection [mm] | Code no. |
SGI 6s | ODF × ODF solder |
¼ x ¼ | — | 014-0034 |
SGI 10s | ODF × ODF solder |
3/8 x 3/8 | — | 014-0035 |
SGI 12s | ODF × ODF solder |
½ x ½ | — | 014-0036 |
SGI 16s | ODF × ODF solder |
5/8 x 5/8 | 16 × 16 | 014-0044 |
SGI 19s | ODF × ODF solder |
¾ x ¾ | 19 × 19 | 014-0047 |
SGI 22s | ODF × ODF solder |
7/8 x 7/8 | 22 × 22 | 014-0039 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Choice of sight glass | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Before choosing a sight glass with moisture indicator, the following should be considered: | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
* Type of refrigerant | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
* water solubility of refrigerant | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
* the level on which a danger signal is required. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Be aware that polyester oil for Non- flammable HFC refrigerants, e.g. R134a, R404A, R407C react with water in a hydrolysis generating acid and alcohol. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The recommended levels of moisture content are usually between 30 and 75 ppm, where hermetic compressors only tolerate very low moisture content, while semi-hermetic and other compressors normally tolerate higher moisture contents in the refrigerant. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The color on the sight glass indicator depends on the moisture content of the refrigerant. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The values under “green/dry” are to be considered as perfect condition meaning full protection against harmful effects from moisture. In other words, the filter drier is working perfectly. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
If the green color starts to fade, the color change has begun and the indicator should therefore be watched more carefully. If the color changes to yellow it is a clear signal that the capacity of the filter drier is exceeded and should be replaced as soon as possible. | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
SGI / SGRI for mineral oil e.g. HCFC refrigerants | ||||||
Mineral oil e.g. R22 | Moisture content ppm = parts per million | |||||
SGI / SGRI | ||||||
25 °C | 43 °C | |||||
Green/ dry | Intermed. color | Yellow/ wet | Green/ dry | Intermed. color | Yellow/ wet | |
< 150 | 150 – 300 | > 300 | < 250 | 250 – 500 | > 500 |